Step-by-step instructions on how to apply Rubio Monocoat DuroGrit to wood siding.

<p id="isPasted">Consult the <a href="https://www.rubiomonocoatusa.com/cdn/shop/files/Rubio_Monocoat_DuroGrit_TDS_English.pdf">TDS</a> prior to using DuroGrit.</p><h2 id="materials-needed">Materials needed</h2><ul><li>Sanding machines and sandpaper</li><li>Vacuum</li><li><a href="https://www.rubiomonocoatusa.com/products/exterior-wood-cleaner">Exterior Wood Cleaner</a></li><li><a href="https://www.rubiomonocoatusa.com/products/durogrit">DuroGrit</a></li><li><a href="https://www.rubiomonocoatusa.com/products/wide-lip-can-opener" title="Rubio Monocoat Can Opener">Paint can opener</a></li><li>Stir stick</li><li>Firm bristle paint brush</li><li>Nitrile gloves</li></ul><h2 id="video">Video</h2><p><span class="fr-video fr-deletable fr-rv fr-fvc fr-dvb fr-draggable" contenteditable="false" draggable="true"><iframe width="100%" src="https://www.youtube.com/embed/0lKOG7z3gyY?&amp;wmode=opaque&amp;rel=0" frameborder="0" allowfullscreen class="fr-draggable"></iframe></span><br></p><h2 id="application-process">Application process</h2><h3 id="preparation">Preparation</h3><ol><li>We recommend allowing the newly installed wood to weather outdoors for about 4-6 weeks (except oak).<ul><li>When this is not possible, sand the wood scratch-free with 80 grit sandpaper to open the wood pores.</li><li>Allow already installed new wood or wood containing natural wood extractives (oak, red cedar, afzelia, redwood, &#x2026;) and especially hardwood (ip&#xE9;, teak, merbau, &#x2026;) to weather outdoors for about 4-6 weeks. This will allow the water-soluble substances to come out of the wood and will allow the wood to absorb the DuroGrit better.</li><li>Note: New, water-repellent pressure-treated wood must be allowed to dry and weather for approximately 6-12 months before doing the surface preparation and coating.</li></ul></li><li><a href="https://knowledge.rubiomonocoatusa.com/en-US/how-to-use-exterior-wood-cleaner-on-siding-283430">Clean the siding with Exterior Wood Cleane</a>r and let it dry.</li></ol><h3 id="application">Application</h3><p>Only work in frost-free and dry conditions and avoid application of DuroGrit when rain is expected within 10 hours of application.</p><ol><li>Tape off anything that should not be treated or could be splashed, smeared, or prone to overlap.</li><li>Stir the DuroGrit a few minutes before use.</li><li>&#xA0;Apply the product evenly to the siding with a good quality, firm bristle paintbrush, suitable for waterborne coatings. Work in the direction of the wood installation, always covering the full length. For vertically installed boards, this means from top to bottom, and for horizontally installed wood from left to right (or vice versa). So never stop in the middle of a board but only at a natural break (e.g. a seam, edge, staircase, etc.). Work in small sections of approximately 1 or 2 boards wide. Always apply sufficient product and brush again afterward to avoid start/stop and brush marks (remember not to exert too much pressure on the brush).<ul><li>Tip: Maintain a wet edge to avoid lap marks.</li><li>Errors created during application (start marks, brush marks, lap marks, &#x2026;) can be touched up on the wet siding up to 15 minutes after application (depending on the weather conditions). Apply a little extra DuroGrit on the mark. Put some pressure on your brush so the product that has already been applied dissolves and mixes with the new one. Finally, smooth out until you no longer have brush marks.</li></ul></li><li>Let the siding dry for about 3 hours. Complete curing takes place after 3 days (at 68&#xB0;F / 20&#xB0;C).<ul><li>Keep in mind that low temperatures, poor ventilation, and relative humidity significantly slow down the drying and curing process</li></ul></li></ol><h3 id="clean-up">Clean up</h3><ul><li>Brushes and tools used to apply DuroGrit can be cleaned with water after use.</li></ul><h3 id="maintenance">Maintenance&#xA0;</h3><ul><li>In general we recommend a yearly visual check-up just after the winter season.</li><li>Please check for the presence of the following two points:<ul><li>Dirt &amp; green deposits; clean with low-pressure water and a soft brush or use Exterior Soap (consult Technical Data Sheet before use)</li><li>Fading of colors</li></ul></li><li>If fading of colors occurs, apply a maintenance coat according to the instructions:&#xA0;<ul><li>First clean your wood with Exterior Wood Cleaner.</li><li>Then apply a layer of DuroGrit in the original color. Depending on the degree of fading of the color, dilute DuroGrit with a maximum of 20% water to avoid applying too much product and making the color too opaque.</li></ul></li><li>The frequency of maintenance depends on the weather conditions, exposure, geographical situation, solar orientation, wood type (softwood vs hardwood), and color. In normal weather conditions, every 3-5 years.</li></ul><h2 id="tips">Tips</h2><p>To set you up for success, please review the <a href="https://knowledge.rubiomonocoatusa.com/en-US/durogrit-tips-409395">DuroGrit tips</a>.</p>

How to apply DuroGrit to siding

Step-by-step instructions on how to apply Rubio Monocoat DuroGrit to existing wood siding.

<p id="isPasted">Consult the <a href="https://www.rubiomonocoatusa.com/cdn/shop/files/Rubio_Monocoat_DuroGrit_TDS_English.pdf">TDS</a> prior to using DuroGrit.</p><h2 id="materials-needed">Materials needed</h2><ul><li>Sanding machines and sandpaper</li><li>Vacuum</li><li><a href="https://www.rubiomonocoatusa.com/products/exterior-wood-cleaner">Exterior Wood Cleaner</a></li><li><a href="https://www.rubiomonocoatusa.com/products/durogrit">DuroGrit</a></li><li><a href="https://www.rubiomonocoatusa.com/products/wide-lip-can-opener" title="Rubio Monocoat Can Opener">Paint can opener</a></li><li>Stir stick</li><li>Firm bristle paint brush</li><li>Nitrile gloves</li></ul><h2 id="video">Video</h2><p><span class="fr-video fr-deletable fr-rv fr-fvc fr-dvb fr-draggable" contenteditable="false" draggable="true"><iframe width="100%" src="https://www.youtube.com/embed/WP83ZJg3tlg?&amp;wmode=opaque&amp;rel=0" frameborder="0" allowfullscreen class="fr-draggable"></iframe></span><br></p><h2 id="application-process">Application process</h2><h3 id="preparation">Preparation</h3><ol><li>We recommend allowing the newly installed wood to weather outdoors for about 4-6 weeks (except oak).<ul><li>When this is not possible, sand the wood scratch-free with 80 grit sandpaper to open the wood pores.</li><li>Allow already installed new wood or wood containing natural wood extractives (oak, red cedar, afzelia, redwood, &#x2026;) and especially hardwood (ip&#xE9;, teak, merbau, &#x2026;) to weather outdoors for about 4-6 weeks. This will allow the water-soluble substances to come out of the wood and will allow the wood to absorb the DuroGrit better.</li><li>Note: New, water-repellent pressure-treated wood must be allowed to dry and weather for approximately 6-12 months before doing the surface preparation and coating.</li></ul></li><li><a href="https://knowledge.rubiomonocoatusa.com/en-US/how-to-use-exterior-wood-cleaner-on-siding-283430">Clean the siding with Exterior Wood Cleaner</a> and let it dry.</li></ol><h3 id="application">Application</h3><p>Only work in frost-free and dry conditions and avoid application of DuroGrit when rain is expected within 10 hours of application.</p><ol><li>Tape off anything that should not be treated or could be splashed, smeared, or prone to overlap.</li><li>Stir the DuroGrit a few minutes before use.</li><li>&#xA0;Apply the product evenly to the siding with a good quality, firm bristle paintbrush, suitable for waterborne coatings. Work in the direction of the wood installation, always covering the full length. For vertically installed boards, this means from top to bottom, and for horizontally installed wood from left to right (or vice versa). So never stop in the middle of a board but only at a natural break (e.g. a seam, edge, staircase, etc.). Work in small sections of approximately 1 or 2 boards wide. Always apply sufficient product and brush again afterward to avoid start/stop and brush marks (remember not to exert too much pressure on the brush).<ul><li>Tip: Maintain a wet edge to avoid lap marks.</li><li>Errors created during application (start marks, brush marks, lap marks, &#x2026;) can be touched up on the wet surface up to 15 minutes after application (depending on the weather conditions). Apply a little extra DuroGrit on the mark. Put some pressure on your brush so the product that has already been applied dissolves and mixes with the new one. Finally, smooth out until you no longer have brush marks.</li></ul></li><li>Let the siding dry for about 3 hours. Complete curing takes place after 3 days (at 68&#xB0;F / 20&#xB0;C).<ul><li>Keep in mind that low temperatures, poor ventilation, and relative humidity significantly slow down the drying and curing process</li></ul></li></ol><h3 id="clean-up">Clean up</h3><ul><li>Brushes and tools used to apply DuroGrit can be cleaned with water after use.</li></ul><h3 id="maintenance">Maintenance&#xA0;</h3><ul><li>In general we recommend a yearly visual check-up just after the winter season.</li><li>Please check for the presence of the following two points:<ul><li>Dirt &amp; green deposits; clean with low-pressure water and a soft brush or use Exterior Soap (consult Technical Data Sheet before use)</li><li>Fading of colors</li></ul></li><li id="isPasted">If fading of colors occurs, apply a maintenance coat according to the instructions:&#xA0;<ul><li>First clean your wood with Exterior Wood Cleaner.</li><li>Then apply a layer of DuroGrit in the original color. Depending on the degree of fading of the color, dilute DuroGrit with a maximum of 20% water to avoid applying too much product and making the color too opaque.</li></ul></li><li>The frequency of maintenance depends on the weather conditions, exposure, geographical situation, solar orientation, wood type (softwood vs hardwood), and color. In normal weather conditions, every 3-5 years.</li></ul><h2 id="tips">Tips</h2><p>To set you up for success, please review the <a href="https://knowledge.rubiomonocoatusa.com/en-US/durogrit-tips-409395">DuroGrit tips</a>.</p>

How to apply DuroGrit to weathered siding

Step-by-step instructions on how to re-oil or renovate siding with Rubio Monocoat DuroGrit.

<p id="isPasted">Consult the <a href="https://www.rubiomonocoatusa.com/cdn/shop/files/Rubio_Monocoat_DuroGrit_TDS_English.pdf">TDS</a> prior to using DuroGrit.</p><h2 id="materials-needed">Materials needed</h2><ul><li>Sanding machines and sandpaper</li><li>Vacuum</li><li><a href="https://www.rubiomonocoatusa.com/products/exterior-wood-cleaner">Exterior Wood Cleaner</a></li><li><a href="https://www.rubiomonocoatusa.com/products/durogrit">DuroGrit</a></li><li><a href="https://www.rubiomonocoatusa.com/products/wide-lip-can-opener" title="Rubio Monocoat Can Opener">Paint can opener</a></li><li>Stir stick</li><li>Firm bristle paint brush</li><li>Nitrile gloves</li></ul><h2 id="video">Video</h2><p><span class="fr-video fr-deletable fr-rv fr-fvc fr-dvb fr-draggable" contenteditable="false" draggable="true"><iframe width="100%" src="https://www.youtube.com/embed/BgWOOj-TKt8?&amp;wmode=opaque&amp;rel=0" frameborder="0" allowfullscreen class="fr-draggable"></iframe></span><br></p><h2 id="application-process">Application process</h2><h3 id="preparation">Preparation</h3><ol><li style="font-size: 14px;"><p><span style="font-size: 14px;">Remove all residues of old applications by sanding the surface scratch-free. End with 80-grit sandpaper, do not sand smoother. The smoother you sand, the less product can penetrate in the wood and the less intense the color (and protection) will be.&#xA0;</span></p><ul><li>If your wood is too dirty to start sanding right away, first clean it with either water or Exterior Wood Cleaner. By already removing a lot of dirt beforehand, your sandpaper won&apos;t get clogged up right away when sanding.</li></ul></li><li style="font-size: 14px;"><a href="https://knowledge.rubiomonocoatusa.com/en-US/how-to-use-exterior-wood-cleaner-on-siding-283430">Clean the siding with Exterior Wood Cleaner</a> and let it dry.</li></ol><h3 id="application">Application</h3><p>Only work in frost-free and dry conditions and avoid application of DuroGrit when rain is expected within 10 hours of application.</p><ol><li>Tape off anything that should not be treated or could be splashed, smeared, or prone to overlap.</li><li>Stir the DuroGrit a few minutes before use.</li><li>&#xA0;Apply the product evenly to the siding with a good quality, firm bristle paintbrush, suitable for waterborne coatings. Work in the direction of the wood installation, always covering the full length. For vertically installed boards, this means from top to bottom, and for horizontally installed wood from left to right (or vice versa). So never stop in the middle of a board but only at a natural break (e.g. a seam, edge, staircase, etc.). Work in small sections of approximately 1 or 2 boards wide. Always apply sufficient product and brush again afterward to avoid start/stop and brush marks (remember not to exert too much pressure on the brush).<ul><li>Tip: Maintain a wet edge to avoid lap marks.</li><li>Errors created during application (start marks, brush marks, lap marks, &#x2026;) can be touched up on the wet surface up to 15 minutes after application (depending on the weather conditions). Apply a little extra DuroGrit on the mark. Put some pressure on your brush so the product that has already been applied dissolves and mixes with the new one. Finally, smooth out until you no longer have brush marks.</li></ul></li><li>Let the siding dry for about 3 hours. Complete curing takes place after 3 days (at 68&#xB0;F / 20&#xB0;C).<ul><li>Keep in mind that low temperatures, poor ventilation, and relative humidity significantly slow down the drying and curing process</li></ul></li></ol><h3 id="clean-up">Clean up</h3><ul><li>Brushes and tools used to apply DuroGrit can be cleaned with water after use.</li></ul><h3 id="maintenance">Maintenance&#xA0;</h3><ul><li>In general we recommend a yearly visual check-up just after the winter season.</li><li>Please check for the presence of the following two points:<ul><li>Dirt &amp; green deposits; clean with low-pressure water and a soft brush or use Exterior Soap (consult Technical Data Sheet before use)</li><li>Fading of colors</li></ul></li><li id="isPasted">If fading of colors occurs, apply a maintenance coat according to the instructions:&#xA0;<ul><li>First clean your wood with Exterior Wood Cleaner.</li><li>Then apply a layer of DuroGrit in the original color. Depending on the degree of fading of the color, dilute DuroGrit with a maximum of 20% water to avoid applying too much product and making the color too opaque.</li></ul></li><li>The frequency of maintenance depends on the weather conditions, exposure, geographical situation, solar orientation, wood type (softwood vs hardwood), and color. In normal weather conditions, every 3-5 years.</li></ul><h2 id="tips">Tips</h2><p>To set you up for success, please review the <a href="https://knowledge.rubiomonocoatusa.com/en-US/durogrit-tips-409395">DuroGrit tips</a>.</p>

How to re-oil or renovate siding with DuroGrit

Step-by-step instructions on how to apply Rubio Monocoat DuroGrit to outdoor wood furniture.

<p id="isPasted">Consult the <a href="https://www.rubiomonocoatusa.com/cdn/shop/files/Rubio_Monocoat_DuroGrit_TDS_English.pdf">TDS</a> prior to using DuroGrit.</p><h2 id="materials-needed">Materials needed</h2><ul><li>Sanding machines and sandpaper</li><li>Vacuum</li><li><a href="https://www.rubiomonocoatusa.com/products/exterior-wood-cleaner">Exterior Wood Cleaner</a></li><li><a href="https://www.rubiomonocoatusa.com/products/durogrit">DuroGrit</a></li><li><a href="https://www.rubiomonocoatusa.com/products/wide-lip-can-opener" title="Rubio Monocoat Can Opener">Paint can opener</a></li><li>Stir stick</li><li>Firm bristle paint brush</li><li>Nitrile gloves</li></ul><h2 id="video">Video</h2><p><span class="fr-video fr-deletable fr-rv fr-fvc fr-dvb fr-draggable" contenteditable="false" draggable="true"><iframe width="100%" src="https://www.youtube.com/embed/DUbOwJpc3Ow?&amp;wmode=opaque&amp;rel=0" frameborder="0" allowfullscreen class="fr-draggable"></iframe></span><br></p><h2 id="application-process">Application process</h2><h3 id="preparation">Preparation</h3><ol><li>We recommend allowing new wood to weather outdoors for about 4-6 weeks (except oak).<ul><li>When this is not possible, sand the wood scratch-free with 80 grit sandpaper to open the wood pores.</li><li>Allow already installed new wood or wood containing natural wood extractives (oak, red cedar, afzelia, redwood, &#x2026;) and especially hardwood (ip&#xE9;, teak, merbau, &#x2026;) to weather outdoors for about 4-6 weeks. This will allow the water-soluble substances to come out of the wood and will allow the wood to absorb the DuroGrit better.</li><li>Note: New, water-repellent pressure-treated wood must be allowed to dry and weather for approximately 6-12 months before doing the surface preparation and coating.</li></ul></li><li><a href="https://knowledge.rubiomonocoatusa.com/en-US/how-to-use-exterior-wood-cleaner-on-furniture-283432">Clean the outdoor furniture with Exterior Wood Cleaner&#xA0;</a>and let it dry.</li></ol><h3 id="application">Application</h3><p>Only work in frost-free and dry conditions and avoid application of DuroGrit when rain is expected within 10 hours of application.</p><ol><li>Stir the DuroGrit a few minutes before use.</li><li>&#xA0;Apply the product evenly to the outdoor furniture with a good quality, firm bristle paintbrush, suitable for waterborne coatings. Work in the direction of the wood installation, always covering the full length. For vertically installed boards, this means from top to bottom, and for horizontally installed wood from left to right (or vice versa). So never stop in the middle of a board but only at a natural break (e.g. a seam, edge, staircase, etc.). Work in small sections of approximately 1 or 2 boards wide. Always apply sufficient product and brush again afterward to avoid start/stop and brush marks (remember not to exert too much pressure on the brush).<ul><li>Tip: Maintain a wet edge to avoid lap marks.</li><li>Errors created during application (start marks, brush marks, lap marks, &#x2026;) can be touched up on the wet surface up to 15 minutes after application (depending on the weather conditions). Apply a little extra DuroGrit on the mark. Put some pressure on your brush so the product that has already been applied dissolves and mixes with the new one. Finally, smooth out until you no longer have brush marks.</li></ul></li><li>Let the outdoor furniture dry for about 3 hours. Complete curing takes place after 3 days (at 68&#xB0;F / 20&#xB0;C).<ul><li>Keep in mind that low temperatures, poor ventilation, and relative humidity significantly slow down the drying and curing process</li></ul></li></ol><h3 id="clean-up">Clean up</h3><ul><li>Brushes and tools used to apply DuroGrit can be cleaned with water after use.</li></ul><h3 id="maintenance">Maintenance&#xA0;</h3><ul><li>In general we recommend a yearly visual check-up just after the winter season.</li><li>Please check for the presence of the following two points:<ul><li>Dirt &amp; green deposits; clean with low-pressure water and a soft brush or use Exterior Soap (consult Technical Data Sheet before use)</li><li>Fading of colors</li></ul></li><li id="isPasted">If fading of colors occurs, apply a maintenance coat according to the instructions:&#xA0;<ul><li>First clean your wood with Exterior Wood Cleaner.</li><li>Then apply a layer of DuroGrit in the original color. Depending on the degree of fading of the color, dilute DuroGrit with a maximum of 20% water to avoid applying too much product and making the color too opaque.</li></ul></li><li>The frequency of maintenance depends on the weather conditions, exposure, geographical situation, solar orientation, wood type (softwood vs hardwood), and color. In normal weather conditions:<ul><li>Vertical surfaces: every 3-5 years</li><li>Horizontal surfaces: up to 2 years</li></ul></li></ul><h2 id="tips">Tips</h2><p>To set you up for success, please review the <a href="https://knowledge.rubiomonocoatusa.com/en-US/durogrit-tips-409395">DuroGrit tips</a>.</p>

How to apply DuroGrit to outdoor furniture

Step-by-step instructions on how to apply Rubio Monocoat DuroGrit to decking.

<p id="isPasted">Consult the <a href="https://www.rubiomonocoatusa.com/cdn/shop/files/Rubio_Monocoat_DuroGrit_TDS_English.pdf">TDS</a> prior to using DuroGrit.</p><h2 id="materials-needed">Materials needed</h2><ul><li>Sanding machines and sandpaper</li><li>Vacuum</li><li><a href="https://www.rubiomonocoatusa.com/products/exterior-wood-cleaner">Exterior Wood Cleaner</a></li><li><a href="https://www.rubiomonocoatusa.com/products/durogrit">DuroGrit</a></li><li><a href="https://www.rubiomonocoatusa.com/products/wide-lip-can-opener" title="Rubio Monocoat Can Opener">Paint can opener</a></li><li>Stir stick</li><li>Firm bristle paint brush</li><li>Nitrile gloves</li></ul><h2 id="video">Video</h2><p><span class="fr-video fr-deletable fr-rv fr-fvc fr-dvb fr-draggable" contenteditable="false" draggable="true"><iframe width="100%" src="https://www.youtube.com/embed/LHI8M5zk6CE?&amp;wmode=opaque&amp;rel=0" frameborder="0" allowfullscreen class="fr-draggable"></iframe></span><br></p><h2 id="application-process">Application process</h2><h3 id="preparation">Preparation</h3><ol><li>We recommend allowing the newly installed wood to weather outdoors for about 4-6 weeks (except oak).<ul><li>When this is not possible, sand the wood scratch-free with 80 grit sandpaper to open the wood pores.</li><li>Allow already installed new wood or wood containing natural wood extractives (oak, red cedar, afzelia, redwood, &#x2026;) and especially hardwood (ip&#xE9;, teak, merbau, &#x2026;) to weather outdoors for about 4-6 weeks. This will allow the water-soluble substances to come out of the wood and will allow the wood to absorb the DuroGrit better.</li><li>Note: New, water-repellent pressure-treated wood must be allowed to dry and weather for approximately 6-12 months before doing the surface preparation and coating.</li></ul></li><li><a href="https://knowledge.rubiomonocoatusa.com/en-US/how-to-use-exterior-wood-cleaner-on-decking-273757">Clean the decking with Exterior Wood Cleaner&#xA0;</a>and let it dry.</li></ol><h3 id="application">Application</h3><p>Only work in frost-free and dry conditions and avoid application of DuroGrit when rain is expected within 10 hours of application.</p><ol><li>Stir the DuroGrit a few minutes before use.</li><li>&#xA0;Apply the product evenly to the decking with a good quality, firm bristle paintbrush, suitable for waterborne coatings. Work in the direction of the wood installation, always covering the full length. For vertically installed boards, this means from top to bottom, and for horizontally installed wood from left to right (or vice versa). So never stop in the middle of a board but only at a natural break (e.g. a seam, edge, staircase, etc.). Work in small sections of approximately 1 or 2 boards wide. Always apply sufficient product and brush again afterward to avoid start/stop and brush marks (remember not to exert too much pressure on the brush).<ul><li>Tip: Maintain a wet edge to avoid lap marks.</li><li>Errors created during application (start marks, brush marks, lap marks, &#x2026;) can be touched up on the wet surface up to 15 minutes after application (depending on the weather conditions). Apply a little extra DuroGrit on the mark. Put some pressure on your brush so the product that has already been applied dissolves and mixes with the new one. Finally, smooth out until you no longer have brush marks.</li></ul></li><li>Let the decking dry for about 3 hours. Complete curing takes place after 3 days (at 68&#xB0;F / 20&#xB0;C).<ul><li>Keep in mind that low temperatures, poor ventilation, and relative humidity significantly slow down the drying and curing process</li></ul></li></ol><h3 id="clean-up">Clean up</h3><ul><li>Brushes and tools used to apply DuroGrit can be cleaned with water after use.</li></ul><h3 id="maintenance">Maintenance&#xA0;</h3><ul><li>In general we recommend a yearly visual check-up just after the winter season.</li><li>Please check for the presence of the following two points:<ul><li>Dirt &amp; green deposits; clean with low-pressure water and a soft brush or use Exterior Soap (consult Technical Data Sheet before use)</li><li>Fading of colors</li></ul></li><li id="isPasted">If fading of colors occurs, apply a maintenance coat according to the instructions:&#xA0;<ul><li>First clean your wood with Exterior Wood Cleaner.</li><li>Then apply a layer of DuroGrit in the original color. Depending on the degree of fading of the color, dilute DuroGrit with a maximum of 20% water to avoid applying too much product and making the color too opaque.</li></ul></li><li>The frequency of maintenance depends on the weather conditions, exposure, geographical situation, solar orientation, wood type (softwood vs hardwood), and color. In normal weather conditions, up to 2 years.</li></ul><h2 id="tips">Tips</h2><p>To set you up for success, please review the <a href="https://knowledge.rubiomonocoatusa.com/en-US/durogrit-tips-409395">DuroGrit tips</a>.</p>

How to apply DuroGrit to decking

Step-by-step instructions on how to re-oil or renovate decking with Rubio Monocoat DuroGrit.

<p id="isPasted">Consult the <a href="https://www.rubiomonocoatusa.com/cdn/shop/files/Rubio_Monocoat_DuroGrit_TDS_English.pdf">TDS</a> prior to using DuroGrit.</p><h2 id="materials-needed">Materials needed</h2><ul><li>Sanding machines and sandpaper</li><li>Vacuum</li><li><a href="https://www.rubiomonocoatusa.com/products/exterior-wood-cleaner">Exterior Wood Cleaner</a></li><li><a href="https://www.rubiomonocoatusa.com/products/durogrit">DuroGrit</a></li><li><a href="https://www.rubiomonocoatusa.com/products/wide-lip-can-opener" title="Rubio Monocoat Can Opener">Paint can opener</a></li><li>Stir stick</li><li>Firm bristle paint brush</li><li>Nitrile gloves</li></ul><h2 id="video">Video</h2><p><span class="fr-video fr-deletable fr-rv fr-fvc fr-dvb fr-draggable" contenteditable="false" draggable="true"><iframe width="100%" src="https://www.youtube.com/embed/91pmaUm4Zlw?&amp;wmode=opaque&amp;rel=0" frameborder="0" allowfullscreen class="fr-draggable"></iframe></span><br></p><h2 id="application-process">Application process</h2><h3 id="preparation">Preparation</h3><ol><li style="font-size: 14px;"><p><span style="font-size: 14px;">Remove all residues of old applications by sanding the surface scratch-free. End with 80-grit sandpaper, do not sand smoother. The smoother you sand, the less product can penetrate in the wood and the less intense the color (and protection) will be.&#xA0;</span></p><ul><li>If your wood is too dirty to start sanding right away, first clean it with either water or Exterior Wood Cleaner. By already removing a lot of dirt beforehand, your sandpaper won&apos;t get clogged up right away when sanding.&#xA0;</li></ul></li><li style="font-size: 14px;"><a href="https://knowledge.rubiomonocoatusa.com/en-US/how-to-use-exterior-wood-cleaner-on-decking-273757">Clean the decking with Exterior Wood Cleaner</a> and let it dry.</li></ol><h3 id="application">Application</h3><p>Only work in frost-free and dry conditions and avoid application of DuroGrit when rain is expected within 10 hours of application.</p><ol><li>Stir the DuroGrit a few minutes before use.</li><li>&#xA0;Apply the product evenly to the decking with a good quality, firm bristle paintbrush, suitable for waterborne coatings. Work in the direction of the wood installation, always covering the full length. For vertically installed boards, this means from top to bottom, and for horizontally installed wood from left to right (or vice versa). So never stop in the middle of a board but only at a natural break (e.g. a seam, edge, staircase, etc.). Work in small sections of approximately 1 or 2 boards wide. Always apply sufficient product and brush again afterward to avoid start/stop and brush marks (remember not to exert too much pressure on the brush).<ul><li>Tip: Maintain a wet edge to avoid lap marks.</li><li>Errors created during application (start marks, brush marks, lap marks, &#x2026;) can be touched up on the wet surface up to 15 minutes after application (depending on the weather conditions). Apply a little extra DuroGrit on the mark. Put some pressure on your brush so the product that has already been applied dissolves and mixes with the new one. Finally, smooth out until you no longer have brush marks.</li></ul></li><li>Let the decking dry for about 3 hours. Complete curing takes place after 3 days (at 68&#xB0;F / 20&#xB0;C).<ul><li>Keep in mind that low temperatures, poor ventilation, and relative humidity significantly slow down the drying and curing process</li></ul></li></ol><h3 id="clean-up">Clean up</h3><ul><li>Brushes and tools used to apply DuroGrit can be cleaned with water after use.</li></ul><h3 id="maintenance">Maintenance&#xA0;</h3><ul><li>In general we recommend a yearly visual check-up just after the winter season.</li><li>Please check for the presence of the following two points:<ul><li>Dirt &amp; green deposits; clean with low-pressure water and a soft brush or use Exterior Soap (consult Technical Data Sheet before use)</li><li>Fading of colors</li></ul></li><li id="isPasted">If fading of colors occurs, apply a maintenance coat according to the instructions:&#xA0;<ul><li>First clean your wood with Exterior Wood Cleaner.</li><li>Then apply a layer of DuroGrit in the original color. Depending on the degree of fading of the color, dilute DuroGrit with a maximum of 20% water to avoid applying too much product and making the color too opaque.</li></ul></li><li>The frequency of maintenance depends on the weather conditions, exposure, geographical situation, solar orientation, wood type (softwood vs hardwood), and color. In normal weather conditions, up to 2 years.</li></ul><h2 id="tips">Tips</h2><p>To set you up for success, please review the <a href="https://knowledge.rubiomonocoatusa.com/en-US/durogrit-tips-409395">DuroGrit tips</a>.</p>

How to re-oil or renovate decking with DuroGrit

Tips, tricks, and best practices when using Rubio Monocoat DuroGrit

<ul><li>To determine the desired color, always do a small test first with one of our color samples on identically sanded and prepared wood.</li><li>A good preparation is crucial for good protection. Always prepare the wood with Exterior Wood Cleaner, including if the wood is new.</li><li>Stir the product well before application. When using several containers at one site, it is recommended to mix them for an even result.</li><li>Avoid direct sunlight on the surface during application and only work in frost-free conditions and when weather conditions are dry.</li><li>In case of rough/weathered wood, highly absorbent woods, or for deck application, you can add up to a maximum 20% water to the DuroGrit for a better spreadability of the product.</li><li>Do not cover and do not place heavy objects on the surface until it is completely cured.</li><li>Only use our maintenance and cleaning products.</li><li>Our products are developed with environmentally friendly ingredients. However, some people can be allergic to certain elements. Therefore, we advise wearing gloves during application to protect your skin.</li><li>Tape off first and work between the grooves. Tape off anything that should not be treated, splashed, smeared, or spilled on, including anything sensitive to overlaps.</li><li>The product can also be applied with a spray gun.</li></ul>

DuroGrit tips

Coverage and spread rate information for DuroGrit.

<p id="isPasted">The coverage, or spread rate, for <a href="https://www.rubiomonocoatusa.com/products/durogrit">DuroGrit</a> is 80-150 ft&#xB2;/L.</p><p>Here is the estimated* coverage broken down by packaging size:<br><strong>30 ml</strong> = sample<br><strong>1 liter</strong> = 80-150 ft&#xB2;<br><strong>2.5 liter</strong> = 200-375 ft&#xB2;</p><p><span style="font-size: 12px;">*These are estimates. Your results may vary based on wood species, water popping, sanding, etc... It is always recommended to make a sample in order to calculate the exact usage.</span></p>

DuroGrit coverage

Main website

Rubio Monocoat USA

A sustainable, wood-fiber fortified and water-soluble oil that colors and protects exterior wood in 1 single layer.